Skip to content

Resources

How to identify a commercial floor type before it gets cleaned

Name the floor before you pick the pad, the chemical or the machine. This guide shows how to tell vinyl, linoleum, rubber, tile, stone, terrazzo, concrete and wood apart by what you see and what the building records say, then points you to the right care guide and a printable walk sheet.

Request a quoteCall (408) 533-0557

Polished concrete lobby meeting a carpet tile suite and rubber stair treads, commercial floor type identification

Printable checklist

Download the PDF

Why the floor type decides the cleaning method

Every care step on a hard floor follows from what the floor is made of. Armstrong’s maintenance chart treats vinyl composition tile as a polish-based floor that gets stripped and refinished, yet it holds linoleum to solutions of pH 10 or less, and a stripper that is routine on the first floor is wrong for the second. The same Armstrong guide warns that rubber and linoleum get mistaken for vinyl, and that luxury vinyl gets mistaken for wood or laminate. When that happens, the wrong pad or stripper goes down on a floor that was never meant to take it.

Use this page to put a name on each floor in your building from what you can see and what the paperwork says, then open the care guide for that surface. The walk sheet at the bottom lets a facility team record the floor in each area once, so every crew, vendor and new hire works from the same answer.

Start with what you can see: size, seams, grout and strips

Four clues sort most commercial floors before any product comes out. Look at the unit size: a grid of foot-square tiles, long planks, big rubber squares or one continuous sheet. Look at the joints: grout lines point to ceramic, porcelain, quarry tile or stone, thin metal or plastic strips in a chip-filled surface point to terrazzo, and welded seams far apart point to sheet goods. Feel it underfoot: rubber is soft and quiet, while tile and stone are hard and cold. Then find where the shine sits: as a film of polish on top, as a sheen inside a concrete slab, or as a glossy coating laid over it.

These are things you may notice, not tests a manufacturer publishes, so take them as a first read. The building’s own records settle the question. The finish schedule in the construction drawings and the flooring submittals from the original build or the last remodel name the product and its maker, and that maker’s care guide tells you what the floor needs.

Floor type identifier: what to look for and where to read next

Work down the table one area at a time. The middle columns show what to look for on the floor and in the files; the last column links our care guide for that surface, with its schedule and the signs it needs more than routine work.

Floor typeWhat you may noticeWhat to check in the recordsCare guide to read next
VCT (vinyl composition tile)A grid of tiles, most often 12 x 12 in; mottled color that runs through each tile; a hard, uncushioned feel; shine that comes from polishThe product line, and whether it left the factory with a finishVCT floor care
Luxury vinyl tile or plankPlanks or tiles printed to look like wood or stone, with the same grain or vein showing up again a few pieces later; warmer and softer than real tile or stoneGlue-down, click or loose-lay install, and whether the wear layer has a urethane factory finishLVT and LVP floor care
Sheet vinylOne continuous surface with few seams, set far apart; thin welded seam lines; no tile gridWhether it is a slip-retardant sheet made to go without polishSheet vinyl floor care
LinoleumMarbled color through the thickness; a warm, matte feel; on a newer floor, a yellow cast that looks different where rugs or furniture satThe brand, its factory finish and the maker’s support lineLinoleum floor care
RubberSoft, quiet and a little springy; raised discs or diamond texture; large square tiles; matte unless someone finished itWhether a floor finish has ever been appliedRubber floor cleaning
Ceramic and porcelain tileHard, cold, rigid tile with grout joints; glazed facesGlazed or polished porcelain, and any sealer used at installCeramic and porcelain tile care
Quarry tileRed, brown or gray unglazed tile, mostly in kitchens; thick, with wide grout joints; the same color at a chipped edgeThe sealer used and when it was last appliedQuarry tile kitchen floors
Marble and natural stoneVeining and a fine texture (often marble); shell or fossil marks (often limestone); crystals or flecks with little veining (often granite)The stone’s name, which tells you whether acid will etch itMarble and natural stone floor care
TerrazzoChips of marble or glass set in a smooth surface, divided by thin metal or plastic strips in a grid or patternThe binder: epoxy or cementTerrazzo floor care
Polished concreteSand or stone showing in a flat slab; saw-cut control joints; a sheen that sits in the concrete, with no film on topThe densifier system and the gloss level specifiedPolished concrete floor care
Sealed concreteA bare-looking slab where a drop of water beads up instead of soaking inThe sealer or cure-and-seal product appliedSealed concrete floor care
Epoxy coatingA seamless glossy or colored film over concrete, sometimes with color flakes or a coved base; chips at edges and along forklift pathsThe coating system and who installed itEpoxy floor cleaning
Urethane resin, including urethane cementA resinous layer over the slab with no tile joints, where water sits on the surfaceWhether the resin system is epoxy or urethane, and its makerUrethane cement floor care
Maple sports floorNarrow parallel strips with natural grain that never repeats; game lines under the finish; a sprung feel in gymsThe finish maker’s instructions and the date of the last screen and recoatMaple sports floor care
HardwoodWood strips or planks whose grain never repeats; a pattern that does repeat points to luxury vinyl insteadSolid or engineered wood, and the finish on topHardwood floor care

Resilient floors: the polish question tells them apart

Vinyl tile, luxury vinyl, sheet vinyl, linoleum and rubber look close enough to fool a new crew, and the biggest difference between them in practice is what each one does with floor finish. Armstrong’s chart lists an acrylic factory finish on its VCT and calls it a polish-based floor, so polish is part of normal care. Its luxury vinyl and sheet products carry a urethane factory finish where polish is optional, and its Safety Zone slip-retardant sheet takes no polish and no buffing at all.

Linoleum and rubber sit apart again. Forbo neither recommends nor requires floor finish on Marmoleum with Topshield pro, and says a floor cared for by its guide never needs stripping. Armstrong rubber tile has no factory finish, and Roppe’s smooth rubber tile needs none, though it still needs daily care. So before a strip and wax goes on the calendar, make sure the floor is one that takes it. Our floor stripping and waxing crews check the floor type first, and hard floor care covers the surfaces that are cleaned and protected without a strip.

Concrete floors: sealed, polished or coated

Three concrete floors can look alike from the doorway and need different care. The ASCC’s Concrete Polishing Council defines polished concrete as a slab whose surface has been processed to a specified gloss, and a floor with a film-forming coating on top does not meet that definition. A densifier, a silicate that reacts inside the concrete, is part of how a polished slab gets its hardness and shine. So the real question is where the shine lives: in the slab, or in a layer over it.

A few drops of water answer most of that. Sherwin-Williams and FloorGuard both publish a water drop test: put coin-sized drops in several spots and watch them. Water that soaks into the slab quickly points to bare or penetrating-sealed concrete; water that beads and sits points to a sealer, a coating or something else on the surface. The two suppliers give different timings, so read the result as a fast soak versus beading rather than against a stopwatch. Peeling or chipped edges along forklift paths show a layer laid over the slab, which points to an epoxy or urethane coating. Our concrete floor scrubbing crews set pads and chemistry by which of the three is in front of them.

Natural stone and terrazzo: why acid matters

Natural stone falls into two families. Marble, travertine, limestone and onyx are calcareous, made mostly of calcium carbonate, and acid etches them. Granite, slate, sandstone and quartzite are siliceous and hold up better, though the Natural Stone Institute still advises against acid cleaners on them because trace minerals in the stone react. Hydrofluoric acid, found in some rust removers, attacks every stone.

An older stone industry care guide (MIA, 2004) describes an acid drop test on a hidden spot, and warns in the same passage that the test etches the stone, that a sealer can hide the result and that the acid is corrosive. Leave that one to a stone professional. Terrazzo has its own question: the NTMA care guide asks owners to learn which binder they have, cement or epoxy, and to use only neutral-pH products on either, and a terrazzo contractor can tell you which system is down. Solum cleans and polishes marble and terrazzo, and we look at the stone with you on the walkthrough before any work is planned.

The one thing to keep off each floor

Each maker or trade group names a mistake that does lasting harm. This table puts one per floor in a single place, with the guide it comes from. Many of these guides are older editions, so check the current care document for the product in your building as well.

FloorKeep off itWhose care guide says so
VCTBrown or black pads, and aggressive mop-on, no-rinse strippers on tile under two years oldAHF VCT maintenance instructions, 2026
Luxury vinylRubber-backed mats and petroleum products, which can stain for good; treated or sticky dust mopsArmstrong care chart, 2016; Mannington care guide, 10/26
Sheet vinylPolish or buffing on a slip-retardant sheet built to go without polishArmstrong care chart, 2016
LinoleumAny solution above pH 10, and traditional wet strippingArmstrong care chart, 2016; Forbo Marmoleum care guide, 05/26
RubberKerosene, naphtha and other solvents, highly alkaline or acid cleaners, and mop-and-shine productsRoppe rubber tile care, 2018
Ceramic and porcelainFluorine-based cleaners such as hydrofluoric acid, acid or solvent cleaners on polished porcelain, and no-rinse cleanersDaltile tile care page
Quarry tileNo-rinse enzymatic or acid cleaners, which soften grout when heat and food residue are presentDaltile quarry tile care page
Marble, limestone and travertineVinegar, lemon and acid-based cleanersMIA stone care guide, 2004; Natural Stone Institute
TerrazzoAnything that is not neutral pHNTMA terrazzo care guide, 2012
Polished and sealed concreteAcid cleaners; on polished concrete, burnishing a slab younger than 28 daysCurecrete maintenance instructions, 2024
Epoxy and urethane coatingsAcids, caustics, stiff bristles and dragging heavy loads across the surfaceFloorGuard care and maintenance guide
Maple sports floorExcess water, and floor covers left down too longMFMA floor surface protection, 2025

When to stop and ask

If the floor still has no name after the walk and the records, slow down. Daltile strongly advises testing any cleaning product on a small area first, and that habit protects every other floor type too. The makers run support lines for exactly this: Forbo sends linoleum questions to its US product support team, Tarkett and Johnsonite route rubber questions to technical services, and NTMA points terrazzo owners to a local terrazzo contractor. For a hard stone problem, both stone guides say to bring in a stone professional.

Older resilient floors deserve extra care, because old floors may contain asbestos. The Resilient Floor Covering Institute publishes recommended work practices for removing resilient flooring that may contain it. The safe default is simple: never sand or dry-scrape an old floor no one can identify, and follow those practices and local rules before anyone works on it.

Printable floor type identifier

Download the floor type identifier sheet and take it on your next walk. It has a line for each area with what you saw, the floor you think it is and the records you checked, plus the quick cues and the one thing to keep off each floor. Once it is filled in, keep it with the building’s maintenance file and hand a copy to every floor vendor, so the method always matches the material. When you know what is underfoot, our floor care schedule planner shows what that floor’s maker asks for, and commercial floor cleaning methods explains the scrubbing, burnishing and refinishing work behind it.

Get help naming your floors

Not sure what is underfoot in every room? Ask for a free walkthrough. On a site visit we go room by room beside you, naming each floor, then send a written quote that lists the care planned for every surface, with the work set after closing time or across a weekend while your building stays open as usual. Request your walkthrough.

A few useful answers

Common questions

What is the quickest way to tell VCT from luxury vinyl?

Look at the pattern. VCT is a grid of tiles, most often a foot square, with mottled color that runs through each tile, and its shine comes from polish. Luxury vinyl is printed to look like wood or stone, so the same grain or vein turns up again a few planks along. The flooring submittals settle any doubt.

How can I tell whether a concrete floor is sealed?

Put a few coin-sized drops of water in different spots. If they soak in fast, the slab is bare or has a penetrating sealer. If they bead up and sit, a sealer or coating is on the surface. Read it as soak versus bead, because the suppliers who publish the test give different timings.

Should I test a stone floor with vinegar to see if it is marble?

No. The stone guide that describes an acid drop test also warns that it etches the stone, which is the very damage you are trying to avoid. Leave the test to a stone professional, or check the stone’s name in the building records.

Where in the building records is the floor type listed?

Look for the finish schedule in the construction drawings and the flooring submittals from the original build or the last remodel. They give the product and its maker, and the maker’s care guide follows from there.

What should we do with an old floor nobody can identify?

Hold off on stripping, sanding or dry scraping, test any product on a hidden spot first, and call the maker’s technical line if the brand is known. Old resilient floors can contain asbestos, so follow the RFCI work practices and local rules before any aggressive work.

Does Solum identify the floors on its walkthrough?

Yes. The free walkthrough looks at the material, finish and condition of each floor, and the written quote names the floor type in every area with the care we plan for it.